How close to the stove to install MH6 Miracle Heat

General Q&A

How close to the stove to install MH6 Miracle Heat

Postby qbot » Thu Dec 08, 2011 12:26 pm

Where can I get the installation instructions for MH6 Miracle Heat from US Stove?
qbot
 
Posts: 35
Joined: Mon Mar 14, 2011 9:29 pm

Re: How close to the stove to install MH6 Miracle Heat

Postby Nutmeg Auto » Thu Dec 08, 2011 12:33 pm

MIRACLE HEAT
OWNERS MANUAL

UNITED STATES STOVE COMPANY
227 Industrial Park Rd., South Pittsburg, TN 37380
HOW TO ORDER REPAIR PARTS
THIS MANUAL WILL HELP YOU TO OBTAIN EFFICIENT, DEPENDABLE
SERVICE FROM THE HEATER, AND ENABLE YOU
TO ORDER REPAIR PARTS CORRECTLY.
KEEP THIS MANUAL IN A SAFE PLACE FOR FUTURE REFERENCE.
WHEN WRITING, ALWAYS GIVE THE FULL MODEL NUMBER
WHICH IS ON THE NAMEPLATE ATTACHED TO THE INSIDE OF
THE CABINET DOOR OF THE HEATER.
WHEN ORDERING REPAIR PARTS OR OPTIONS,
ALWAYS GIVE THE FOLLOWING INFORMATION
AS SHOWN IN THIS LIST:
1. The PART NUMBER
2. The PART DESCRIPTION
3. The MODEL NUMBER: (6") (8")
4. The SERIAL NUMBER:
________________
BEFORE INSTALLING YOUR HEATER, FILL IN THE SERIAL
NUMBER OF YOUR HEATER IN THE SPACE PROVIDED ABOVE.
United States Stove Company
227 Industrial Park Rd.
P.O.Box 151
South Pittsburg, TN 37380
(423) 837-2100
STOP
Waste Heat Reclaimer
Read these instructions before operating or
installing the unit.
Congratulations on your purchase of the "Miracle Heat" Heat Reclaimer, a heat
efficiency product from United States Stove Company, North America's oldest
manufacturer of solid fuel appliances.
Every wood or coal stove or furnace manufactured to date is not totally efficient.
This means that heat which could be utilized is going up each and every chimney.
The "Miracle Heat" Heat Reclaimer is designed to utilize a part of that lost heat,
and yet let enough heat pass through the chimney to maintain proper draft and
temperature so that creosote and soot formation is kept to a minimum. "Miracle
Heat" Heat Reclaimer has a quiet, dependable 100 CFM fan that promotes heat
circulation to improve overall efficiency. The amount of heat actually recovered
will depend upon the type of fuel that is burned and the type of heating appliance
on which the Miracle Heat is mounted.
Chimney draft will likewise have a significant effect on the efficient operation of
your Miracle Heat. The greater your draft, the more you need a Miracle Heat.
But if your draft is insufficient, your Miracle Heat will not operate as efficiently,
and you will possibly contribute to your draft deficiency.
Your Miracle Heat heat exchanger is designed to work well on nearly every solid
fuel stove manufactured, but was specifically designed for older model stoves
which are less efficient by design. If has also proved very effective when used
in conjunction with a catalytic damper, as the after-burned gases from a catalytic
damper are themselves quite hot, and, again, represent waste heat (though
harmful wood products are being burned off).
CAUTION
I.
DO NOT...
GENERAL INSTRUCTIONS:
Your Miracle Heat should not be installed by anyone
inexperienced with such work or not familiar with pre
cautions required and not capable of complying with all
requirements set by the various authorities having
jurisdiction. If you are unfamiliar withsuch an
installation, then do not attempt to install it yourself. Have it done by a
qualified installer, one who is well versed in heating equipment venting, its
use and safety.
1. Do not use a Miracle Heat that has a smaller flue diameter than
the flue outlet on your fireplace, heater, or stove.
PART NO. DESCRIPTION QTY.
168274Top/Side panel weld. (Mode 1
68275Top/Side panel weld. (Model 1
222801Back/Bottom panel (Model ) 1
22803Back/Bottom panel (Model 1
3682736" Flue pipe/tubing Assy. (Mode
682758" Flue pipe/tubing Assy. (Model MH8 ) 1
480248Electric Motor1
589359Fan blade1
680232Power supply cord1
789524M. heat front brass trim1
880249Thermostat1
985630Product Label1
1 083348#8x3/8" Pan hd. sheet metal screw1 8
1 183351#8x3/8" hex hd. sheet metal screw1 0
1 2833248-32x1-1/4" machine screw1
1 3832978-32 Hex Nut1
1 480250Power cord clamp1
1 583350Steel spacer1
*85854M. heat UPC code label1
* Not Shown
*80252Closed end connectors2
*83349#8-32 Nylon insert jam L. nut2
*80109Strain relief bushing1
http://noes.net/MH6.pdf
Nutmeg Auto
 
Posts: 43
Joined: Sun Mar 13, 2011 11:06 pm


Return to Questions & Answers

Who is online

Users browsing this forum: No registered users and 2 guests

cron